Greenmaster compatible controller KXTL-230 FHTL Astek Wired |Console connector 5 narrow pins | power supply to console
Special Price
€149.00
Regular Price
€200.00
In stock
SKU
X2LB-scheda-TD300Xgreenmaster-cablata-5pin-piccolo-passo2.5
Greenmaster compatible controller KXTL-230 FHTL Astek Wired |Console connector 5 narrow pins | power supply to console. Pin spacing 2.5mm.
Control board for treadmills new, suitable to replace Greenmaster boards.
Console connector with 5 close pins. The board is adaptable to all types of treadmills.
Control voltage 0-10 V calibrated on Greenmaster specifications. Compared to the original board, some protections have been introduced:
- Motor line protection to increase safety in the event of a mosfet short circuit.
- Input Signal Protection: if the potentiometer is shorted, or the customer has turned on with the potentiometer regulated at full speed, the board will stop instead of going to full speed.
- Protection on sudden commands: if the customer turns the speed very quickly by mistake, the board will respond by increasing the speed gradually.
- incoming AC line protection fuse. Wiring To simplify the installation, the board is provided with all the wires, for easy installation in the treadmill.
The wiring provided with this board is with 5 narrow pin. Control board for treadmills (motor controller board), compatible with type Greenmaster, FH, JD and KXTL, already wired. Tens of thousands of treadmills have been manufactured with Greenmaster boards.
They have been distributed by numerous brands around the world. So, there are different types of Greenmaster boards: to understand the right model for you, you will need to check two main points: type of transformer and type of connector.
Single secondary transformer controller
If there are only four wires on the transformer on-board, this means your board is a single secondary transformer board. In this case, normally, the console is powered by an external power supply (usually batteries).
In this case, you will need to purchase a single secondary control board, which is cheaper.
Double secondary transformer controller
If there are six cables on the transformer on-board, this means that your board is a double secondary transformer board. In this case, the controller also powers the console of your treadmill.
Connectors
Both boards single and double are supplied with different connectors. You should choose the correct connector for your board to simplify installation.
Connector types normally used are:
For single secondary transformer controllers
wide 5 evenly-spaced pins connector
narrow connector with 5 close pin
For double secondary transformer controllers
Wide connector with 5 pins, total length approximately 2 cm, evenly-spaced pins
Narrow connector with 5 pins, total length about 1 cm, close pins. This is the type that is provided on this page
Wide type connector, 3 + 2 pins (with space between 3 and 2), total length about 2.5 cm Power supply
The board provided in this listing has power supply for the console.
The most common board models replaced with this board are 301S067 KXTL-230, FHTL-230 301S185.
Many treadmills have been equipped with this board, such as Reebok, Diadora, Cammax, Atala, Energetics, Sprinter, Greenfit, Well-Net, Roger Black, Everlast, Momentum, Get Fit, Body Perfect, Wega Fitness,
Fitness Pro. We recommend you to carefully check the wiring because boards with different connectors were manufactured with the same model number over time.
Console connector with 5 close pins. The board is adaptable to all types of treadmills.
Control voltage 0-10 V calibrated on Greenmaster specifications. Compared to the original board, some protections have been introduced:
- Motor line protection to increase safety in the event of a mosfet short circuit.
- Input Signal Protection: if the potentiometer is shorted, or the customer has turned on with the potentiometer regulated at full speed, the board will stop instead of going to full speed.
- Protection on sudden commands: if the customer turns the speed very quickly by mistake, the board will respond by increasing the speed gradually.
- incoming AC line protection fuse. Wiring To simplify the installation, the board is provided with all the wires, for easy installation in the treadmill.
The wiring provided with this board is with 5 narrow pin. Control board for treadmills (motor controller board), compatible with type Greenmaster, FH, JD and KXTL, already wired. Tens of thousands of treadmills have been manufactured with Greenmaster boards.
They have been distributed by numerous brands around the world. So, there are different types of Greenmaster boards: to understand the right model for you, you will need to check two main points: type of transformer and type of connector.
Single secondary transformer controller
If there are only four wires on the transformer on-board, this means your board is a single secondary transformer board. In this case, normally, the console is powered by an external power supply (usually batteries).
In this case, you will need to purchase a single secondary control board, which is cheaper.
Double secondary transformer controller
If there are six cables on the transformer on-board, this means that your board is a double secondary transformer board. In this case, the controller also powers the console of your treadmill.
Connectors
Both boards single and double are supplied with different connectors. You should choose the correct connector for your board to simplify installation.
Connector types normally used are:
For single secondary transformer controllers
wide 5 evenly-spaced pins connector
narrow connector with 5 close pin
For double secondary transformer controllers
Wide connector with 5 pins, total length approximately 2 cm, evenly-spaced pins
Narrow connector with 5 pins, total length about 1 cm, close pins. This is the type that is provided on this page
Wide type connector, 3 + 2 pins (with space between 3 and 2), total length about 2.5 cm Power supply
The board provided in this listing has power supply for the console.
The most common board models replaced with this board are 301S067 KXTL-230, FHTL-230 301S185.
Many treadmills have been equipped with this board, such as Reebok, Diadora, Cammax, Atala, Energetics, Sprinter, Greenfit, Well-Net, Roger Black, Everlast, Momentum, Get Fit, Body Perfect, Wega Fitness,
Fitness Pro. We recommend you to carefully check the wiring because boards with different connectors were manufactured with the same model number over time.
We found other products you might like!
-
Greenmaster compatible board KXTL-230 KX8-230C FH Astek WIRED | Console connector 3 + 2 pins | power supply consoleSpecial Price €149.00 Regular Price €200.00
-
Greenmaster compatible controller KXTL-230, JD, FH Astek WIRED | Console connector with 5 equally spaced pins | power supply consoleSpecial Price €149.00 Regular Price €200.00