Motor compatible with Greenmaster industrial corp. GM25110
Special Price
€144.99
Regular Price
€300.00
In stock
SKU
X3-MT-180-LM-8.2-CON-FASCE-8-10-11
Greenmaster motors are now obsolete and out of production. The motor provided is compatible with the Greenmaster industrial corp. motors GM25110, see attached photos.
Warning: the motor provided is about 28 cm long, if there is not enough space to mount it, please contact us for the purchase of a shorter motor .
DC Motor with power 1.5, corresponding to about 3 HP peak.
Suitable to replace motors with the following specifications:
V: 180 to 230V
HP: between 1.25 and 2.0
8.2 cm diameter motor body
= Between 4000 RPM and 5600 RPM
Installation
Check for proper lubrication of the running belt
Check the correct tension of the drive belt and the running belt
Remove the old engine
Connect the new engine (faston M + corresponds to the red wire M- corresponds to the black wire.
After installation, use the following instructions to prevent damage to the replacement motor
Regularly lubricate the deck
Always start with your feet on the side rails (FIRST start the walking 1km / h, climb POI)
Keep a walking speed over 5km / h
After exercising, check if the motor overheats. If the Moro reaches 45 ° C verify correct installation and maintenance.
Special cases
If the board does not have a speed sensor, it is necessary to calibrate the new motor. This is done by rotating the trimmer speed of 1/4 turn at a time as per attached picture
If the mounting holes do not match those on the treadmill, you can alternatively drill the mounting plate of the motor so the holes match those on the motor or fix the engine with metal bands like a bolted joint (available from hardware stores).
If the motor touches the outer casing of the treadmill, position the spacer washers (available from hardware stores) under the casing to keep it slightly raised.
Warning: the motor provided is about 28 cm long, if there is not enough space to mount it, please contact us for the purchase of a shorter motor .
DC Motor with power 1.5, corresponding to about 3 HP peak.
Suitable to replace motors with the following specifications:
V: 180 to 230V
HP: between 1.25 and 2.0
8.2 cm diameter motor body
= Between 4000 RPM and 5600 RPM
Installation
Check for proper lubrication of the running belt
Check the correct tension of the drive belt and the running belt
Remove the old engine
Connect the new engine (faston M + corresponds to the red wire M- corresponds to the black wire.
After installation, use the following instructions to prevent damage to the replacement motor
Regularly lubricate the deck
Always start with your feet on the side rails (FIRST start the walking 1km / h, climb POI)
Keep a walking speed over 5km / h
After exercising, check if the motor overheats. If the Moro reaches 45 ° C verify correct installation and maintenance.
Special cases
If the board does not have a speed sensor, it is necessary to calibrate the new motor. This is done by rotating the trimmer speed of 1/4 turn at a time as per attached picture
If the mounting holes do not match those on the treadmill, you can alternatively drill the mounting plate of the motor so the holes match those on the motor or fix the engine with metal bands like a bolted joint (available from hardware stores).
If the motor touches the outer casing of the treadmill, position the spacer washers (available from hardware stores) under the casing to keep it slightly raised.
Motor for DC treadmill / running platforms. compatible with Greenmaster industrial corp. GM25110.
We found other products you might like!
-
Greenmaster Controller | Framework with external power supply | 5 pin narrow comb connectorSpecial Price €149.00 Regular Price €200.00
-
Controller Greenmaster | FH058W-H Square | 5 pinSpecial Price €139.00 Regular Price €270.00
-
Greenmaster Controller | Framework with external power supply | 3+2 pin comb connectorSpecial Price €149.00 Regular Price €200.00